Take it to a stihl dealer thats been at it a while, They may be able to look at the saw and know right off what it is. Stihl chainsaw serial number location, Gp Bikes Unlock Code, selmer sax serial number list. Download Crack Software, Serial Number, Activation Code. How the heck do you pro's read the serial number to tell year. Stihl Chainsaw Serial Number Check Carb adjustment. To adjust the carburetor in the chainsaw: Start the saw, turn the adjusting screw for high and low revolutions to the stop. Turn it back one and a half turns. Warm up the saw for 5-10 minutes. Set idle screw. With the right settings, the circuit will not move on the bus at idle. Number of Drive Links in Reels Type 100' Reel 1/4' 3/8' STIHL PICCO™.325' 3/8'.404' 2400 1640 1840 1640 1480 ANSI B175.1 Chain Saw Kickback Standard STIHL’s green and yellow color code system serves to identify STIHL bars and chains with different kickback reduction characteristics. How to Find Out if My Stihl Saw Was Stolen Write down the serial number for the chainsaw. Stihl assigns all the chainsaws it manufactures a distinct number. Look for a dealer's sticker on the chainsaw. Call your local law enforcement agency. Ask the officer to find out if the chainsaw shows up on the National Equipment Register list of stolen equipment. Write down the serial number for the chainsaw. Stihl assigns all the chainsaws it manufactures a distinct number. When people buy the chainsaw new at a dealer, often the dealer takes care of registering the chainsaw with the Stihl company. You can call Stihl or contact them through email to learn if the previous owner ever reported it as stolen.

Stihl Serial Number Check
Stihl Serial Number Check Blacklist
Stihl Trimmer Serial Number Lookup

Most serial numbers are stamped in the motor housing or crankcase to the left or right of the muffler looking down from the top on a flat surface. They will in most cases be 9 digits long and begin with the number 1, 2 or 5.

Will a 10% (E10) blend of ethanol hurt my gas-powered STIHL product?

All STIHL gasoline-powered engines can be used with up to a 10% (E10) blend of ethanol in the gasoline/engine oil mix. We also recommend that if a unit will be left unused for more than 30 days that it be stored 'dry.' This means emptying the fuel tank and then restarting and letting the unit run until all the fuel is consumed and the engine stops. For maximum performance and engine life expectancy, we also recommend using STIHL HP Ultra 2-cycle engine oil.

Note: STIHL recommends use of fuel with no more than 10% ethanol content. Using fuel with greater than 10% ethanol content may cause damage to your equipment and may void your STIHL warranty. Learn More…

My chainsaw will start and idle but won't run or stalls when I go to full throttle. What's wrong?

There are several things you can check. First, make sure that you are using fresh fuel mix (never store or use fuel mix older than 60 days in can or fuel tank). Second, clean spark arrester screen in the muffler. Third, replace fuel filter in fuel tank. Fourth, clean or replace air filter. If none of these work, please take the machine to your local authorized STIHL servicing Dealer for evaluation.
Learn more about fuel concerns
Read more about storing your outdoor power equipment

Why does my chainsaw flood?

The most common reason is due to too many attempts trying to start the machine in the choke position. When starting a unit, make sure to follow the starting instructions in your instruction manual. The manual provides the proper instruction for starting procedures, but there are many conditions that may affect how the unit starts. Digital picture frame pu-10w manual. A good rule of thumb to follow is to remember that when placing the switch control to the full choke setting, more liquid fuel and less air flow into the combustion chamber in order to create a higher chance for ignition. Pulling the rope more than two to three times in this setting may flood the engine. The operator should move the Master Control Lever™ or choke lever from the full choke setting after three to four pulls even if the engine does not fire. Moving the lever to the next setting, the half choke or part throttle position will allow more air into the combustion chamber and help resolve the flooding condition.

Why does my saw leak bar oil?

The way our units lubricate a chain, most of the oil is distributed around the inside of the bar rails as it is circulated by the oil reservoirs in each drive link of the chain. The amount of oil being circulated inside the bar at any given time can be between .3 and .5 oz. As a general rule of physics, the oil will be pulled down by gravity once the chain stops turning, collecting at the bottom of the bar and seeping through the chain to puddle underneath the bar & chain assembly as well as under the drive sprocket. The fact that it appears to be continuing to seep after the unit is cut off for several days is owed to the viscosity of the oil and the anti-flinging compound (lithium) mixed with the oil at the refinery. These factors give the oil a very thick consistency, which in turn explains a slower flow rate. This condition is deemed to be normal for any chainsaw with a similar bar & chain lubricating system.
If the unit continues to seep oil after a few days, the problem may be the vacuum relief valve located in the side of the engine housing between the oil output hole and the bar stud(s). This valve has an internal spring and ball type arrangement with the ball pressed against the vent hole of the casing of the valve, when the tank develops a vacuum from the normal process of the oil being pumped out. The ball is pulled away from the hole, allowing air to enter into the tank and break the vacuum so that oil can continue to flow to the bar and chain assembly. Once the vacuum is relieved, the spring pushes the ball back against the hole of the valve casing. Sometimes debris may become trapped between the ball and the hole. This would cause the oil to keep 'weeping' because there must be some measure of vacuum in the tank to keep the oil from flowing freely once the unit is shut down. More often than not, all one needs to do is to take a small pin or needle and push it into the hole of the valve (identifiable as a small silver disk with a small hole in the center) about 6 or 7 times to loosen the debris. This should re-seal the orifice and keep the oil from seeping from the output hole when the saw is stored.

How do I adjust the bar and chain on my chainsaw?

Please refer to your instruction manual under the headings: Mounting Bar and Chain, Tensioning the Saw Chain and Checking Chain Tension.

What is kickback?

Kickback occurs when the moving saw chain near the upper quadrant of the bar nose contacts a solid object or is pinched. The reaction of the cutting force of the chain causes a rotational force on the chainsaw in the direction opposite to the chain movement. This may fling the bar up and back in an uncontrolled arc mainly in the plane of the bar. Under some cutting circumstances the bar moves towards the operator, who may suffer severe or fatal injury. Kickback may occur when the nose of the guide bar is pinched unexpectedly, unintentionally contacts solid material in the wood or is incorrectly used to begin a plunge or boring cut. It may also occur during limbing. The greater the force of the kickback reaction, the more difficult it becomes for the operator to control the saw. Many factors influence the occurrence and force of the kickback reaction. These include chain speed, the speed at which the bar and chain contact the object, the angle of contact, the condition of the chain and other factors.

What protective gear is required for chainsaw operation?

Where do I find my serial number?

What do I need to know about chainsaw bar and chain lubrication?

For automatic and reliable lubrication of the saw chain and guide b

Stihl Serial Number Check